Q.1

For a circular column having its ends hinged, the slenderness ratio isThe l/d ratio of the column is

  • 80
  • 57
  • 40
  • 20
Q.2

Which steel member section among the following combinations can carry maximum load ?

  • A pair of angles welded on opposite sides of a gusset plate, but not tack welded
  • A pair of angles welded on opposite sides of a gusset plate, and tack welded along its length.
  • A pair of angles back to back on same side of a gusset plate, and tack welded.
  • A pair of angles on same side of a gusset plate, but not tack welded
Q.3

Ratio of the width of the car parking area required at kerb forparking relative toparking is approximately

  • 0.5
  • 0.7
  • 0.8
  • 2.0
Q.4

In the plane truss shown above, how many numbers have zero force?

  • 3
  • 5
  • 7
  • 9
Q.5

Which among the following assumptions are made in the design roof trusses ?
Roof truss is restrained by the reactions
Axes of the members meeting at a joint intersect at a common point
Riveted joints act as frictionless hinges
Loads act normal to roof surface
Select the correct answer using the codes given below:

  • 1, 2 and 4
  • 2, 3 and 4
  • 1, 3 and 4
  • 1, 2 and 3
Q.6

If two triangulation signals of 6.m height each, are to be just visible over ground mutually, what is the maximum distance between their locations on the ground surface ?

  • 10 km
  • 20 km
  • 30 km
  • 40 km
Q.7

What is eutrophication of lakes primarily due to ?

  • Multiplication of bacteria
  • Excessive inflow of nutrients
  • Increase in benthic organisms
  • Thermal and density currents
Q.8

Consider the following statements regarding the swedish circle method of analysing stability of slopes :
It is a general method of analysing stability of slopes.
It satisfied only the overall moment equation of equilibirum.
It considers the forces action on the sides of individual slices.
It gives a factor of safety which are on the safeside.
Of the statements :

  • 1, 2 and 3 are correct
  • 1, 2 and 4 are correct
  • 2, 3 and 4 are correct
  • 1, 3 and 4 are correct
Q.9

In the plane truss shown above, how many numbers have zero force?

  • 3
  • 5
  • 7
  • 9
Q.10

Bricks are burnt at a temperature range of

  • 500° to 700°C
  • 700° to 900°C
  • 900° to 1200°C
  • 1200° to 1500°C
Q.11

Tensile strength of concrete is measured by

  • direct tension test in the universal testing machine
  • applying compressive load along the diameter of the cylinder
  • applying third point loading on a prism
  • applying tensile load along the diameter of the cylinder
Q.12

Non-collodial liguids are :

  • Newtonian fluids
  • Plastic fluids
  • ideal fluids
  • dilatant fluids
Q.13

A 4-hour rainfall in a catchment ofkm2 produces rainfall depths of 6.2 cm and 5.0 cm in successive 2-hour unit periods. Assuming the φ index of the soil to be 1.2 cm/hour, the run-off volume in ha-m will be

  • 16
  • 22
  • 1600
  • 2200
Q.14

Drop panel is a structural component in :

  • grid floor
  • flat plate
  • flat slab
  • slab-beam system of floor
Q.15

Water is to be pumped at the rate of 0.m3/s from a 4 m deep ground level tank to an overhead tank. The difference in levels of the full tank levels of these tanks ism. What is the approximate power required for operating aefficient centrifugal pump ?

  • 7.5 kW
  • 6.0 kW
  • 3.9 kW
  • 3.2 kW
Q.16

Under load, the void ratio of a submerged saturated clay decreases from 1.to 0.What will be the ultimate settlement of the 2 m thick clay due to consolidation ?

  • 20 mm
  • 40 mm
  • 80 mm
  • 160 mm
Q.17

The following data pertain to a waste-water sample :
Initial D.O. = 8 mg/l
Final D.O. = 2 mg/l
Dilution = 1%.
The B.O.D. of the given wastewater sample is

  • 600 mg/l
  • 6 mg/l
  • 0.6 mg/l
  • 1 mg/l
Q.18

Consider the following statements with respect to tunnelling methods:
Full face excavation is suitable for small size tunnel of short length in compact rock. It is not suitable in urban areas.
Heading and Benching method is suitable for soft rock tunnelling of medium size.
Drift method is suitable for large tunnels in difficult or incompetent rock.
Which of the statements given above are correct ?

  • 1 and 3
  • 1, 2 and 3
  • 2 and 3
  • 1 and 2
Q.19

What is range of values of Poisson's ratio for ductile materials ?

  • 0.10 to 0.15
  • 0.16 to 0.20
  • 0.21 to 0.24
  • 0.25 to 0.33
Q.20

Consider the following statements :
The critical path in a network plan of a project
helps in planning efficient time schedule
indicates the shortest path in time
helps in crashing the project judiciously
helps in encouraging discipline in execution.
Of these statements :

  • 1, 3 and 4 are correct
  • 1, 2, 3 and 4 are correct
  • 1 and 4 are correct
  • 2 and 3 are correct
Q.21

A ship is berthed in a chamber and lifted by principles of buoyancy. Such a chmber is called

  • Dry dock
  • Web dock
  • Floating dock
  • Refuge dock
Q.22

Ultimate strength of cement is influenced by which one of the following ?

  • Tricalcium silicate
  • Dicalcium silicate
  • Tricalcium aluminate
  • Tetracalcium alumino-ferrite
Q.23

If p is the specific gravity of the material used in the design of a masonry dam of triangular section, then the ratio between the height and base width of the dam for structural safety and stability is equal to

  • 2p
  • p
  • 1/p
  • 1/p
Q.24

The ratio of the flexural strengths to two beams of square c. oss-section, the first beam being placed with its top and bottom sides horizontally and the second beam being placed with one diagonal horizontally, is

  • 3
  • 1/3
  • 1/2
  • 2
Q.25

Compression index of a soil helps to determine

  • total time required for consolidation
  • time required for 50 percent consolidation
  • total settlement of clay water
  • pre-consolidation pressure of clay
Q.26

Two reservoirs are connected by two pipes A and B of same and length in series. If the diamerer of A islarger than that of B, what is the ratio of head loss in A to that of B ?

  • 0.77
  • 0.59
  • 0.50
  • 0.27
Q.27

A brick masonry wall of nominal thicknessmm carries an axial load ofkN/m and another load ofkN/m acting at an eccentricity ofmm. The resultant eccentricity and eccentricity ratio are respectively

  • 19 mm, 0.095
  • 19 mm, 1.00
  • 22 mm, 1.10
  • 24 mm, 1.20
Q.28

What is the value of camber rate that should be provided in case of WBM pavement surface in an area of heavy rainfall ?

  • 1 in 30
  • 1 in 48
  • 1 in 60
  • 1 in 72
Q.29

Following data refer to precise measurement of an angle A on the field :
(i) 2A = 20°- weight 2
(ii) 4A = 40°- weight 3
What is the most probable value of angle A ?

  • 10°01'06"
  • 10°02'07"
  • 10°02'51"
  • 10°22'51"
Q.30

A flash mixer of 2.0 m3, with a velocity gradient of mixing mechanisms equal to 660/s, and fluid absolute viscosity of 1.0 x 10-3 Ns/m2 is continuously operated. What is the power input per unit volume ?

  • 360 W
  • 720 W
  • 1440 W
  • 300 W
Q.31

A simply supported beam of span 'L' and uniform flexural rigidly EI, carries a central load 'W' and total uniformly distributed load 'W' throughout the span. The maximum deflection is given by

  • 13 WL3/96 EI
  • 5 WL3/384 EI
  • 5 WL3/96 EI
  • 13 WL3/384 EI
Q.32

For excavating utility trenches with precise control of depth the excavation equipment used is:

  • Hoe
  • Shovel
  • Dragline
  • None of the above
Q.33

Which of the following pairs are correctly matched ?
Alpha iron....non magnetic
Beta iron....strongly magnetic
Gamma iron....non-magnetic and capable of dissolving carbon.
Delta iron....non-magnetic and absorbs very little carbon.
Select the correct answer using the codes given below :

  • 3 and 4
  • 1 and 2
  • 1, 3 and 4
  • 2 and 4
Q.34

Which one of the following pairs is not correctly matched ?

  • Check valve - To check water flow in all directions
  • Sluice valve - To control flow of water through pipe lines
  • Air valve - To release the accumulated air
  • Scour valve - To remove silt in a pipe line
Q.35

A rectangular footing 1 m x 2 m is placed at a depth of 2 m in a saturated clay having an unconfined compressive strength ofkN/m2. According to Skempton, the net ultimate bearing capacity is

  • 420 kN/m2
  • 412.5 kN/m2
  • 385 kN/m2
  • 350 kN/m2
Q.36

The percentage of time in a year during which the cross wind component remains within the limit, is :

  • Wind coverage
  • Headwind
  • Prevailing wind
  • Cross wind
Q.37

Among the following, which is/are not pre-treatment unit (s) ?

  • Bar screen and grit chamber
  • Flow equalization and proportioning tank
  • Neutralization for pH adjustment tank
  • Nutrient removal tank
Q.38

The maximum bending moment at the left quarter point of a simple beam due to crossing of UDL of length shorter than the span in the direction left to right, would occur after the load had just crossed the section by

  • one-fourth of its length
  • half of its length
  • three-fourth of its length
  • its full length
Q.39

Which one of the following statements is correct ?
In a plane truss, influence line values

  • vary parabolically between panel points
  • vary exponentially between panel points
  • vary linearly between panel points
  • vary following a cubic relationship between panel points
Q.40

Consider the following statements relating to the stability of floating as well as submerged bodies :
A submerged body is stable when the centre of gravity is below the centre of buoyancy.
A floating body is stable when the centre of gravity is above the centre of buoyancy.
A floating body is stable when the centre of gravity is below the metacentre.
A submerged body is in stable equilibrium when the centre of gravity coincides with the centre of buoyancy.
Of these statements :

  • 1, 2 and 3 are correct
  • 2, 3 and 4 are correct
  • 1, 2 and 4 are correct
  • 1, 3 and 4 are correct
Q.41

Which one of the following statements is correct ? In the lime-soda process of water softening

  • lime reduces carbonate hardness while soda removes non-carbonate hardness
  • only carbonate hardness is removed
  • lime reduces non-carbonate hardness while soda removes carbonate hardness
  • Only non-carbonate hardness is removed.
Q.42

What is the volume of a 6 m deep tank having rectangular shaped top 6 m x 4 m and botton 4 m x 2 m (computed through the use of prismoidal formula) ?

  • 96 m3
  • 94 m3
  • 92 m3
  • 90 m3
Q.43

'Air binding' may occur in

  • Sewers
  • Artesian well
  • Aerator
  • Filter
Q.44

What is the correct sequence of formation of the following compounds during chlorination of water in which ammonia is present ?
NCl3
NH2Cl
NHCl2
Select the correct answer using the codes given below:

  • 1, 2, 3
  • 2, 3, 1
  • 3, 1, 2
  • 2, 1, 3
Q.45

A torsion member is fabricated from two concentric thin tubes. At the ends, the tubes are welded to rigid discs so that both the tubes are twisted as a unit. The radius of the outer tube is 2r and that of the inner tube is r. If the shear stresses developed in the outer tube is τ, then the shear stress in the inner tube will be.

  • τ
  • 0.25 τ
  • 0.75 τ
  • 0.5 τ
Q.46

What is the discharge corresponding to a critical depth of 1.m in a 3.0 m wide rectangular channel:

  • 4.12 m3/s
  • 4.94 m3/s
  • 8.24 m3/s
  • 12.35 m3/s
Q.47

In the design of storm sewers, time of concentration relevant of determine the

  • rainfall intensity
  • velocity in the sewer
  • time of travel
  • area seven by the sewer
Q.48

Sewage sickness is a term used for

  • persons who become sick after drinking polluted water
  • a treatment plant which does not function properly
  • a stream where the flora and fauna die due to sewage inflow
  • the condition of land where sewage is applied continuously for a long period.
Q.49

The height of a hydraulic jump in a stilling pool was found to becm in a model with lp/lm =The prototype jump height would be

  • 0.6 m
  • 3.6 m
  • 21.6m
  • indeterminable for want of adequate data
Q.50

The following refer to the stability analysis of an earth dam under different conditions :
Stability of D/S slope during steady seepage.
Stability of U/S slope during sudden drawdown.
Stability of U/S and D/S slopes during construction.
Of these statements :

  • 1 and 2 are correct
  • 1 and 3 are correct
  • 2 and 3 are correct
  • 1, 2 and 3 are correct
0 h : 0 m : 1 s