Q.1
You have a 15 pin female connector with the pins in two rows. What could you connect with this?
Q.2
The 34-pin connection on an I/O card is for?
Q.3
After you service a laser printer, you notice dirty print. Which of the following would correct the problem.
Q.4
After you service a laser printer, you notice dirty print. Which of the following would correct the problem?
Q.5
During the boot process, a system first counts memory from where?
Q.6
To test for AC ripple on a PC power supply, you would set the volt/ohm meter for:
Q.7
What resistence in ohms should be displayed ehen testing a speaker in a computer?
Q.8
How much video RAM is needed to display 1024x768 at 24-bit color?
Q.9
The ATAPI compliance is stands for?
Q.10
Which of the following FRUs would be considered both an input/output device?
Q.11
All Operating Systems get their total memory initialized from?
Q.12
IBM's Micro Channel Architecture (MCA) specifies which type of the following bit access widths?
Q.13
Which type of pc card (PCMCIA) slot will allow the insertion of a hard drive?
Q.14
When not in use, it is very important to keep 5 VA diskettes in _____.
Q.15
Which I/O port belongs to LPT2?
Q.16
ESD damage can be caused by:
Q.17
The standard VGA display has _____ pixels in its native graphics mode?
Q.18
What problem can occur if a printer cable is to close to a power cable?
Q.19
How can you totally protect a PC from damage during an electrical storm?
Q.20
How many DMA channels are in an AT-machine?
Q.21
The ESD wrist strap is designed to protect PC Components or Service Technicians ?
Q.22
What Does EISA stand for?
Q.23
Which provides the fastest data access time?
Q.24
When configuring a new network interface card for installation, which of the following would be a valid I/O address?
Q.25
A static jolt of as little of _____ volts can fry most any PC integrated circuit.
Q.26
A standard multimeter is ideal for measuring a monitors high voltage output.
Q.27
COM 4 uses which I/O port?
Q.28
A keyboard locks up intermittently even when replaced with a new keyboard. What is the LEAST likely cause of the problem?
Q.29
You are testing the resistance in Ohms of a fuse on a 2 amp system. If the fuse is good, the meter should read?
Q.30
Which is NOT typically a Field Replaceable Unit?
Q.31
A human cannot feel a static discharge as high as _____ volts.
Q.32
When configuring is a network interface cards without jumpers or plug and play, what is used to set the IRQs?
Q.33
MSD exe does not have information on:
Q.34
What type of FRU is a SCSI host adapter?
Q.35
To find out how much memory is available, you could type _____
Q.36
IBM's Micro Channel Architecture (MCA) specifies which type of the following bit access widths?
Q.37
What is the best ground for a conductive work bench?
Q.38
What command is used to hang up a MODEM when using the "AT Command set"?
Q.39
Current is measured in units of:
Q.40
The standard IRQ for the floppy drive is?
Q.41
What can you use to ensure power is not interrupted, resulting in corrupted data?
Q.42
Which step should you perform first before discharging a CRT?
Q.43
What does the acronym RTS represent?
Q.44
Which is the easiest component to environmentally recycle?
Q.45
What problem can occur if a printer cable is to close to a power cable?
Q.46
Your modem does not respond when you try to dial out. You try another modem on another computer and get the same result. What is the most likely problem?
Q.47
You suspect a virus has entered your computer. What will not be affected by the virus?
Q.48
How would you allow device drivers and TSR's to be loaded into Upper Memory Blocks ?
Q.49
In inkjet technology the droplets of ink are deflected by?
Q.50
Which is the easiest component to environmentally recycle?
0 h : 0 m : 1 s