MCQGeeks
0 : 0 : 1
CBSE
JEE
NTSE
NEET
English
UK Quiz
Quiz
Driving Test
Practice
Games
Quiz
Data Structures Algorithms Ii
1000 Design Steel Structures
Quiz 1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Q.1
What is steel structure design?
a) Branch of structural engineering that deals with the design of steel structures
b) Branch of industrial engineering that deals with the design of steel structures
c) Branch of mechanical engineering that deals with the structural steel design
d) None of the mentioned
Q.2
Which of the following method is best for the design of steel structure?
a) Working Stress Method
b) Earthquake Load Method
c) Limit State Method
d) Ultimate Load Method
Q.3
Which of the following is a type of steel structure design?
a) Continuous design
b) Simple design
c) Semi-continuous steel design
d) All of the mentioned
Q.4
Which of the following is added to steel to increase resistance to corrosion?
a) Copper
b) Carbon
c) Manganese
d) Sulphur
Q.5
Which of the following is a disadvantage of Steel?
a) High durability
b) Reusable
c) High strength per unit mass
d) Fire and corrosion resistance
Q.6
Which of the following is the property of high carbon steel?
a) reduced strength
b) high toughness
c) reduced ductility
d) high strength
Q.7
What is the minimum percentage of chromium and nickel added to stainless steel?
a) 10.5%, 0.5%
b) 0.5%, 10.5%
c) 30%, 50%
d) 2%, 20%
Q.8
High carbon steel is used in ______________
a) structural buildings
b) fire resistant buildings
c) for waterproofing
d) transmission lines and microwave towers
Q.9
Which method is mainly adopted for design of steel structures as per IS code?
a) Earthquake Load Method
b) Ultimate Load Method
c) Limit State Method
d) Working Stress Method
Q.10
What is the net section area of steel plate 40cm wide and 10mm thick with one bolt if diameter of bolt hole is 18mm?
a) 38.2 cm2
b) 24 cm2
c) 578 mm2
d) 465 mm2
Q.11
Which of the following relation is correct?
a) Design Strength = Ultimate strength / Partial factor of safety
b) Design Strength = Ultimate strength + Partial factor of safety
c) Design Strength = Ultimate strength * Partial factor of safety
d) Design Strength = Ultimate strength – Partial factor of safety
Q.12
Which of the following load is to be considered on liquid retaining structure?
a) dynamic load
b) earth pressure
c) hydrostatic load
d) wave and current load
Q.13
Which of the following factors does not influence earthquake resistance design?
a) strength of structure
b) site soil
c) geographical location of structure
d) wind of location
Q.14
Which of the following load combination is not possible?
a) Dead load + imposed load
b) Dead load + wind load + earthquake load
c) Dead load + imposed load + wind load
d) Dead load + imposed load + earthquake load
Q.15
Which of the following is true about bracket connections?
a) They are used to give aesthetic appearance to the structure
b) These connections are used to accommodate less number of bolts
c) Fabrication cost is low
d) More rigid than any other connection
Q.16
Proof stress for minimum bolt tension is :
a) 0.7fyb
b) 0.5fyb
c) 0.7fub
d) 0.5fub
Q.17
Which of the following is not an assumption of first-order elastic analysis of rigid jointed frame?
a) member instability effects cannot be ignored
b) materials behave linearly
c) frame instability effects can be ignored
d) yielding effects can be ignored
Q.18
Which of the following about rivet is correct?
a) labour cost is low
b) removing poorly installed rivet is costly
c) it does not require skilled work
d) causes low level of noise pollution
Q.19
Which of the following is advantage of HSFG bolts over bearing type bolts?
a) high strength fatigue
b) joints are not rigid
c) low static strength
d) bolts are subjected to shearing and bearing stresses
Q.20
In which of the following cases pin connections are not used?
a) tall buildings
b) truss bridge girders
c) diagonal bracing connection
d) hinged arches
0 h : 0 m : 1 s
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Report Question
×
What's an issue?
Question is wrong
Answer is wrong
Other Reason
Want to elaborate a bit more? (optional)
Support mcqgeeks.com by disabling your adblocker.
×
Please disable the adBlock and continue.
Thank you.
Reload page