MCQGeeks
0 : 0 : 1
CBSE
JEE
NTSE
NEET
English
UK Quiz
Quiz
Driving Test
Practice
Games
Quiz
Mechanical Engineering
Engineering Drawing
Quiz 6
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Q.1
When drawing a line using the relative coordinate system a line is created from ________.
0, 0
The ending point of the last line
The beginning point of the last line
None of the above
Q.2
Some traditional board drafters preferred the drafting machine over the parallel straight edge because it could be used without the need for_________.
Circle templates
Triangles
Technical pens
Lettering guides
Q.3
Before starting an isometric drawing in Auto-CAD the drafter needs to ________.
Set the grid to isometric
Set the current layer to Def-points
Turn Object Snap off
Turn Ortho off
Q.4
In this type of auxiliary view, a break line is used to indicate the imaginary break in the views:
Primary
Secondary
Revolved
Partial
Q.5
A projection weld is a type of:
Resistance weld
Arc weld
Gas weld
Fillet weld
Q.6
A back or backing weld is a type of:
Groove weld
Resistance weld
Arc and gas weld
Upset weld
Q.7
Students can complete an associate's degree in drafting which normally takes about __________ years to complete.
One
Two
Three
Four
Q.8
This is an angled surface used on cylinders to make them easier to handle:
Fillet
Taper
Chamfer
Lug
Q.9
This is the theoretically exact size from which limits of size are determined:
Actual Size
Dimensioned size
Production size
Basic size
Q.10
In the section view, the areas that would have been in actual contact with the cutting plane are shown with:
A cutting plane line
Section lining
Visible lines
Lines and arrows
Q.11
The ________ is a standard element of a section view in a technical drawing.
Cutting Plane line
Section lines
Material hatch pattern
All of the above
Q.12
These gears transmit power between shafts whose axes intersect at any angle:
Worm gears
Spur gears
Bevel gears
Racks
Q.13
The standard number of threads per inch for various diameters is the:
Series of thread
Lead
Major diameter
Thread pitch
Q.14
Architectural dimensioning is usually done in ________.
Even numbers
Feet and inches
Feet only
Inches only
Q.15
A partial auxiliary view is used to show only the __________ in the auxiliary view.
Projected inclined plane
The projected top view
The projected side view
None of the above
Q.16
In this type of dimensioning, allowance must be made for bends:
Angular
Tolerance
Datum
Sheet metal
Q.17
The bounding box method for setting up an isometric drawing helps the drafter ________.
Confine the isometric drawing to its maximum size
Figure what lines are to be illustrated vertical and horizontal
Position the isometric drawing in paper space
None of the above
Q.18
When creating your own blocks it is important to avoid drawing any portion of the block in the ________ layer.
Zero
Center line
Hatch
Hidden line
Q.19
There should be a visible gap between the wall and the _________ line.
Dimension
Extension
Center
Leader
Q.20
The condition of a part when it contains the least amount of material is referred to as ________.
Smallest
LMC
MMC
Actual size
Q.21
The typical parts list should include the _________.
Part number
Manufacturing material
Number of parts needed
All of the above
Q.22
One way to evenly space dimensions on a drawing is to use the __________.
Dimension Space tool
Linear tool
Continue tool
Baseline tool
Q.23
A round is a rounded surface on the ________ corner of a part.
Inside
Outside
Radial
Isoplane
Q.24
Using this as a communication and design review tool can help shorten the process and eliminate productivity barriers:
Development plans
Portable document files
The Internet and e-mail
Gantt charts
Q.25
The title block used on working drawings should include the _________.
Sheet number
Line type
Layer set
All of the above
Q.26
The thread note for a typical bolt will include the _________.
Major diameter of the thread
Material
Center line
Offset distance
Q.27
A full scale technical drawing will have a scale factor of ________.
1 : 1
1 : 2
2 : 1
1 : 4
Q.28
When using the direct entry method to create a horizontal line exactly three inches long the drafter should ________ first.
Pull the line from away from the starting point very carefully
Insure that Ortho is on
Enter 3 for the length of the line
Read the coordinate position on the Dynamic Readout
Q.29
Several of the tools used in traditional drafting include the following:
Parallel straight edge
45 degree triangle
Circle template
All of the above
Q.30
This is a flat or rounded tab protruding from a surface, usually to provide a method for attachment:
Lug
Boss
Chamfer
Spot face
0 h : 0 m : 1 s
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Report Question
×
What's an issue?
Question is wrong
Answer is wrong
Other Reason
Want to elaborate a bit more? (optional)
Support mcqgeeks.com by disabling your adblocker.
×
Please disable the adBlock and continue.
Thank you.
Reload page