In a flat belt drive, if the slip between the driver and belt is 1 %, between the belt and follower isand driver and follower pulley diameters are equal, then velocity ratio of the drive will be
The interference may only be avoided if the addendum circles of the two mating gears cut the common tangent to the base circles between the points of tangency.
When the effort is in between the fulcrum and load, the lever is said to be of third type.
The bolts of smaller diameter than Mare not permitted in making fluid tight joints.
The shafts of larger diameter are usually forged and turned to size in a lathe.
The gears are termed as medium velocity gears, if their peripheral velocity is
The design calculations for members subject to fluctuating loads with the same factor of safety, yield the most conservative estimates when using
The groove angle of the pulley for rope drive is usually
A cotter joint is used to connect two __________ rods.
The spigot and socket joint is mostly used for pipes which are burried in the earth.
When a hole of diameter 'd' is punched in a metal of thickness 't', then the force required to punch a hole is equal to (where τu = Ultimate shear strength of the material of the plate)
The permissible stress in the fillet weld isN/mm2. The fillet weld has equal leg lengths ofmm each. The allowable shearing load on the weldment per cm length of the weld is
A turn buckle is used to connect two round rods subjected to tensile loading and requiring subsequent adjustment for tightening or loosening.
If the centre distance of the mating gears having involute teeth is increased, then the pressure angle
The product of the diametral pitch and module is equal to one.
In case of pressure vessels having open ends, the fluid pressure induces
The plasticity is the property of a material which enables it to
A saddle key __________ power through frictional resistance only.
The velocity factor for very accurately cut and ground metallic gears operating at velocities upto __________ is equal to 6/6 + v.
In cylindrical cams, the follower moves
Guest's theory is used for
A screw is said to be over hauling screw, if the
The static tooth load should be __________ the dynamic load.
In the levers of first type, the mechanical advantage is __________ one.
Two rigid plates are clamped by means of bolt and nut with an initial force F. After tightening, a separating force P (P < F) is applied to the lower plate, which in turn acts on the nut. The tension in the both after this is
The set screws are used to prevent relative motion between the two parts.
An open coiled helical compression spring 'A' of mean diametermm is subjected to an axial load W. Another spring 'B' of mean diametermm is similar to spring 'A' in all respects. The deflection of spring 'B' will be __________ as compared to spring 'A'.
A rivet is specified by
The power transmitted by means of a belt depends upon
The included angle for the acme thread is 29°.
The square threads are usually found on
Shaft coupling is used in machinery to
Power screws are used to convert rotary motion into translatory motion.
The load placed at the top of the screw in a mechanical screw jack is prevented from rotation by providing a swivelling mechanism.
The bearings of medium series have capacity __________ over the light series.
The face angle of a bevel gear is equal to
When the bolt is very yielding as compared to the connected members, then the resultant load on the bolt will be equal to the
In thrust bearings, the load acts
Auto frettage is the method of
Which of the following coupling is used to connect two shafts which have both lateral and angular misalignment ?
The process extensively used for making bolts and nuts is
Oldham coupling is used to connect two shafts
The function of the washer is to
The usual proportion for the width of key is (where d = Diameter of shaft or diameter of hole in the hub)
The antifriction bearings
Two shafts will have equal strength, if
During hot working of metals,
According to Indian standard specifications, a grey cast iron designated by 'FGmeans that the
In a multiple V-belt drive, when a single belt is damaged, it is preferable to change the complete set in order to
Please disable the adBlock and continue. Thank you.